Quick Guide To Complete Setek WiFi Extender Setup

With the increase in the usage of the internet, the old WiFi routers are not that much efficient. Though, it seems difficult to change all the setup of the old WiFi router. But, you can extend the range of the old WiFi router with the WiFi extenders. And, for this, Setek WiFi extenders are the best choice. To use the Setek WiFi extender, there is a need to complete the Setek WiFi Extender Setup. The Setek WiFi extenders are the best because they cover a wide range of 2500 square kilometers. Moreover, there will be no more dead zones in that particular area. Therefore, it is always a good idea to have the Setek WiFi Extender and complete its Setek WiFi Extender Setup. Therefore, this blog is going to help you with the steps to complete the setup in two ways: Web browser method and the WPS method. So, let’s start with the procedure of the extender setup.

Steps To Complete Setek WiFi Extender Setup

There are two ways to complete the Setek WiFi Extender Setup. The steps for both ways are defined in the following subsections.

1. Setek WiFi Extender Setup Using The Web Browser 

You can set up your Setek WiFi Extender setup using the web browser on your system. This method is the general method and this will work for everyone unlike the WPS method. Therefore, it is always preferable to complete the Setek Extender WiFi Setup using the web browser method. So, follow the below listed instructions very carefully:

Step 1: first, connect your Setek extender to the power source keeping the distance optimum from the router.

Step 2: When the LED for the power label lights in green color, then start the process of the setup.

Step 3: Then, go to the device in which you want to complete the setup.

Step 4: Now, connect your setup device to the Setek extender’s network either via wireless or wired method.

Step 5: In wired, use ethernet cable or in wireless, open the WiFi settings in the system and connect to Setek network.

Step 6: Then, open the desired web browser.

Step 7: Enter the IP address for the Setek extender i.e. 192.168.10.1 in the URL field.

Step 8: Now, this will open the login screen for the Setek Extender. Or, you may be redirected directly to the setup screen.

Step 9: Enter the default login information in the fields from the sticker over the Setek extender.

Step 10: After the successful login, the screen will show you the list for the available networks in your range.

Step 11: From this list, you will select your main network or home network which you want to extend.

Step 12: Enter the security key for the selected network in the prompt.

Step 13: If the password is right, then you will get connected to the main network, and your signal will be extended.

Step 14: On the successful connection, the WiFi light on the extender will light in the green color.

Step 15: This completed the Setek WiFi extender setup using the web browser method.

Step 16: Unplug the extender from the current location, and connect it at the point from where the signal starts getting weak.

Step 17: Check the WiFi light as it should be green if it is in the main router’s range. If it is in red color, then move your Setek extender a bit closer to the Wifi router.

Step 18: Now, try to connect any wireless device with the extender’s network.

If the device got connected successfully, then you have completed the setup in the right way. Now, next, learn about the WPS method for the Setek WiFi extender setup.

2. Setek WiFi Extender Setup Using WPS Method

There is no doubt that the WPS method is the easiest one. But, it is possible only for those whose routers have a WPS button. Therefore, it is not possible for everyone to follow this method. If your router has the WPS button, then you should follow the instructions given below:

Step 1: For the quick setup, connect the extender to the power source in the same room as that of the router.

Step 2: Wait for some time till the power LED light turns into a solid green color.

Step 3: Then, first, press the WPS button for 2-5 seconds on the Setek extender.

Step 4: After that, immediately press the WPS button on the main router for 2-5 seconds.

Step 5: With this, the WPS lights will start blinking on both the router and the extender.

Step 6: Let them blink for 10-15 seconds as it will take time to get connected with the router.

Step 7: On the successful connection, the blinking lights will get stable into green color on both devices.

Step 8: Unplug the extender from the current location, and connect it at the point from where the signal starts getting weak.

Step 9: Check the WiFi light as it should be green if it is in the main router’s range. If it is in red color, then move your Setek extender a bit closer to the Wifi router.

Step 10: Now, try to connect any wireless device with the extender’s network. If your main WiFi network is password-protected, then enter the same password to get connected with the extender’s network.

So, this completes the Setek WiFi extender setup with the WPS method. So, both the methods are explained for the setup. Now, it depends upon you which to follow for the setup of your extender.

Setek Setup Is Working!

Summing up! The Setek extender is working as its setup has completed successfully. This blog has defined both the methods for the Setek WiFi Extender Setup using the WPS and the browser method. On the successful setup, you can connect your device successfully with the Setek extender’s network. As it has a wide range, therefore, you can connect with the extender’s network anywhere at home.In case, you are finding any difficulty for the Setek WiFi Extender Setup, then ask our expert for help. You will get the expert solution for your issue, and you will be able to connect in the end. So, with the Setek WiFi extender working, get the benefits of the internet in the dead spots as well.