Know The Steps To Do Factory Reset TP Link Extender

Under various circumstances, there may be a need to factory reset your extender. Even for troubleshooting purposes, the factory reset method is used. The factory reset will bring back all the settings again to default. Therefore, it would be just like a new device and you can do the configuration from scratch. Now, if you are looking for the steps to Factory Reset TP Link Extender, then you are in the right place. Moreover, do you know, there are different methods available to Factory Reset TP Link Extender? Well, this blog is going to explain to you all the methods to reset your TP-Link extender. So, let’s check out the steps for all the methods:

Different Methods For Factory Reset TP Link Extender

A factory reset can be required in different conditions. Sometimes, you don’t know about the current credentials for your extender. Then, a factory reset can help you to log in with the default credentials. Sometimes, you know the login credentials, but you want to revert back some of the settings about which you don’t know them. So, for both cases, you can factory reset TP Link extender with the following methods.

• Method 1: Using The Web Browser Login

This method is only helpful when you know about the current admin credential for the extender login. But, you want to revert back to the settings about which you don’t know. Then, in that case, you can factory reset your TP-Link extender with the web browser using the following steps:

Step 1: Make sure your system is connected to the TP-Link extender’s network as only then you can access the login page.

Step 2: Then, launch a web browser such as Google Chrome in your system.

Step 3: Now, either use the IP address 192.168.0.254 or the link tplinkextender.net in the address bar.

Step 4: This will open the Login screen for your TP-Link extender.

Step 5: Then, enter the current username and password of the TP-Link extender in the required fields.

Step 6: Click on the Login button to reach the admin panel.

Step 7: On the admin panel, locate the option System Tools on the left-hand side of the page.

Step 8: Under that, select the option of Backup & Restore.

Step 9: Then, select the option of the Factory Reset.

Step 10: Go with the on-screen instructions being shown on the screen, and reset/reboot your TP-Link extender.

Step 11: Now, you can start the configuration process again for your TP-Link extender.

So, these are the steps for the factory reset using the web browser method. In case, you don't know anything about the login credentials, then follow the methods discussed next for factory reset.

• Method 2: Using The Reset Button At The Back Of Extender

Now, as you don't know about the current credentials, then you can use the reset button present at the back of the extender. Follow the instructions mentioned below:

Step 1: Make sure the power is on for your TP-Link extender.

Step 2: Then, find the reset button present at the back of your extender.

Step 3: Then, press the reset button and keep it pressed for around 2 seconds.

Step 4: Wait for all the LEDs to go off, and then light again.

Step 5: After that, wait for the extender to get rebooted properly.

Step 6: Now, you can start with the procedure for the configuration of your extender on your system.

• Method 3: Hard Reset Using Hidden Reset Option

Some of the extenders don’t come with the proper reset button. Then, in that case, there is a need to locate the hidden reset option at the back of the extender. Therefore, for this, you need to go with the following instructions:

Step 1: Take a needle or any other pin-point object.

Step 2: Now, locate the hidden reset button at the back of your extender which cannot be pressed with the finger.

Step 3: Press the hidden reset button with the pin-point object and hold it for 8-10 seconds.

Step 4: First, all the LEDs will go off, and then will start lighting one by one.

Step 5: Wait for the TP-Link extender to get rebooted properly. 

Step 6: Now, you can start the configuration for the TP-Link extender in your system again.

So, these all are the methods you can follow for the Factory Reset TP Link Extender. Depending upon your case, you can choose the method, and then follow those steps. Once, factory reset is done, you can change the configuration as you want.

Configuration Steps For TP-Link Extender!

As your TP-Link extender is in a factory reset state, therefore, all the settings are in default now. So, you need to complete the login with the following steps in order to configure it:

Step 1: Launch a web browser like Google Chrome in your system.

Step 2: Then, enter the default IP address 192.168.1.1 in the URL field.

Step 3: On the login screen, enter the default credentials mentioned on the label of the TP-Link extender (mostly at the back).

Step 4: Click on the Login button, and again do all the configuration to use your extended network.

So, these are the actual steps in order to configure your TP-Link extender. Make sure, you don’t skip any of the steps, otherwise, there would be again the need for the factory reset.

TP-Link Extender Is Back to Default!

Wrapping up! With Factory Reset TP Link Extender operation, all the settings and data have come to default again. Therefore, now you can use all the default information again for login, or configuration purposes. Whether you know the current credentials or not, all the methods are defined for the Factory Reset TP Link Extender. Still, after the factory reset, if there is an issue with the TP-Link extender, then contact our experts. You will get your query resolved in no time. So, get ready to extend the range of your signal with TP-Link Extenders.